polymurph
a4572b848c
|
2 years ago | |
|---|---|---|
| files | 2 years ago | |
| footprints | 2 years ago | |
| packages | 2 years ago | |
| symbols | 2 years ago | |
| Readme.md | 2 years ago | |
Readme.md
KicED
Edwin and Kerem's KiCad library.
Procedure of restructuring KicED
- Create structure which can be added as submoduse to any KiCAD project.
- Document the process of implementeing the submodule
- Document the process of adding (contributing) a new part.
sources for markdown: https://www.markdownguide.org/extended-syntax/
1. How to use this library
This library is intended to be used as a git submodule inside a git version controlled KiCAD project.
1.1 Adding the library to your KiCAD Project
Go to the desired directory where you want to place the library submodule inside your project. Ther you add KicED as submodule with the following comand.
git submodule add https://git.keydev.me/Kerem/KicED
Then open your KiCAD project and go to Preferencesin the top left corner and select Manage Symbol Libraries....
TODO: explain how to incorperate library into KiCAD project
You will need to add the relative KicED paths with respect to your KiCAD project by using the environment variable ${KIPRJMOD}\<...>
source
- https://git-scm.com/book/en/v2/Git-Tools-Submodules
- https://www.educative.io/answers/how-to-specify-a-branch-tag-when-adding-a-git-submodule
1.2 Updating Library
2. Library Structure
0 = Passive 0 = Resistor 0 = SMD 1 = THT 2 = Array 3 = Mechanical 4 = Special 1 = Capacitor 0 = SMD 1 = THT 2 = Array 3 = Mechanical 4 = Special 2 = Inductors 0 = SMD 1 = THT 2 = Array 3 = Mechanical 4 = Special 4 = Oscillators 0 = Crystal 1 = Oscillator 2 = Resonator 3 = Voltage Controlled 5 = Potentiometer 0 = Adjutable 1 = Rotary 3 = Scale 4 = Slide 5 = Trimmer 6 = Digital 6 = Antenna 0 = Bluetooth 1 = Wifi 2 = Sub-giga 3 = giga 4 = Propritary 5 = GSM/GPS 7 = RF
1 = Active 0 = Transistor 0 = Bipolar 1 = FET 2 = IGBT 3 = TRIAC 4 = SiC 5 = GaN 1 = Diodes 0 = Rectifier 1 = Zener 2 = RF 3 = Bridge 4 = UF 5 = Variable Capacitance 2 = Power 0 = Transitor 1 = Diodes 3 = Module 0 = Half Bridge 1 = Full Bridge 2 = Six packs 4 = Opto 5 = Solid state relay 6 = LED 7 = Opto 8 = Driver 0 = Relay 9 = Switch 0 = High Side Switches
2 = Linear 0 = Op-amp 1 = amplifier 2 = Fuse 3 = Switches 5 = Supervisor 6 = Protection 7 = Power 8 = Special
3 = Power 0 = LDO 0 = Standart 1 = Low Noise 2 = Ultra Low Noise 1 = SMPS 0 = Buck 1 = Boost 2 = Buckboost 3 = Multiple 4 = PMIC 2 = Voltage Reference 3 = led Driver 4 = Gate Driver 5 = Motor Driver 0 = DC 6 = ACDC 0 = module 7 = DCDC 0 = module 8 = Charger
4 = Digital 0 = MCU 0 = 8 Bit 1 = 16 Bit 2 = 32 Bit 0 = Microchip 1 = ST 2 = Ti 3 = Toshiba 4 = Cypress 5 = Infineon 6 = Epson 3 = 64 Bit 1 = FPGA 2 = DSP 3 = ASIC 4 = Audio 5 = Serial 6 = Clocks
5 = Logic 0 = Buffer 1 = Comparator 2 = Counter & Divider 3 = FIFO 4 = Flip Flop 5 = Gates 0 = Inverter 1 = AND 6 = Latches 7 = Shift 8 = BUS 9 = Special
6 = Memory 0 = EEPROM 1 = NAND 2 = EMMC 3 = FLASH 4 = SD
7 = Sensors 0 = Enviroment 1 = Temperature 0 = Digital 1 = Analogic 2 = RTD 3 = Thermistor 4 = Thermocouple 2 = MEMS 0 = Accelerometer 1 = Gyroscope 2 = Pressure 4 = X Dof 3 = Light 4 = Sound 5 = Proximity 6 = Hall 7 = Current 8 = Mechanical 9 = Special
8 = Mechanical 0 = Relay 0 = Monostable 1 = Bistable 1 = Connector 0 = Cable to board 1 = Board to board 2 = Lab 3 = rectangular 4 = Circular 5 = Fiber / RJ 6 = Terminal blocks 7 = Serial 8 = USB 9 = Card Edge 2 = Cooling 3 = Fans 4 = Cables 5 = Mounting 6 = Switches 7 = Button 0 = SMD 1 = THT 8 = Encoders
9 = Boards 0 = Wireless 1 = Digital 3 = Display 4 = Sensor 5 = Analogic 6 = Power 7 = Mehanical 8 = Embedded 9 = Special
10 = Electromechanics (these parts are excluded from board) 0 = Contactors 1 = ACDC_Converters 2 = Resistors 3 = Capacitors 4 = Inductors 5 = Switches